Product ID:R-373 RUBBER INSUL ADHESIVE, 373
MSDS Date:11/01/1991
FSC:8040
NIIN:01-164-6863
MSDS Number: BJNCR

RUBATEX CORP

805 MONROE STREET
BEDFORD, VA 24523
US

Emergency Phone: 703-586-2611

Info Phone: 703-586-2611

Preparer: W.F. CREASY

Cage: IO124

THE CLAREMONT COMPANY

952 MERIDEN, CT 06450 US

Telephone: 800-222-4448 / 203-238-2384

Cage: 52307

22

CAS: 108-88-3

RTECS: XS5250000

Fraction By Weight: 16%

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

140

CAS: 110-54-3

RTECS: MN9275000

Fraction By Weight: 28%

OSHA PEL 500 PPM

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

186

CAS: 67-64-1

RTECS: AL3150000

Fraction By Weight: 36%

OSHA PEL 1000PPM

ACGIH TLV: 750PPM/1000STEL;9293

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:NOTE:TOLUENE (108-88-3) APPEARS ON
NAVY LIST OF OCCUP CHEMICAL REPRO HAZARDS. SEEK CONSULTATION FROM
APPROP HLTH PROFS ABOUT LATEST HAZ LIST INFO & SAFE HNDLG & EXPOS
RECOMS . INHAL:DIZZINESS, B REATHING DIFFICULTY, HEADACHE & LOSS
OFCOORDINATION. EYE:SEVERE IRRITAT, TEARING, REDNESS & BLURRED
(EFTS OF OVEREXPOS)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ:VISION. SKIN:CAN DRY & DEFAT SKIN
CAUSING CRACKS, IRRITATION & DERMATITIS. INGEST:CAN CAUSE GI
IRRITATION, VOMITING, NAUSEA & DIARRHEA.
Medical Cond Aggravated by Exposure:ANESTHESIA, RESPIRATORY TRACT
IRRITATION, DERMITITIS, NAUSEA, VOMITING.

First Aid:INHAL: REMOVE TO FRESH AIR. IF BREATHING STOPS, APPLY
ARTIFICIAL RESPIRATION AND SEEK MD IMMED. EYES: FLUSH WITH LARGE
QUANTITIES OF WATER FOR 15 MINUTES. SKIN: WASH THOROUGHLY WITH SOAP
& WATER & SEE MD. INGEST: DO NOT INDUCE VOMITING, CAN CAUSE
CHEMICAL PNEUMONITIS EDEMA. CONTACT MD IMMEDIATELY.

Flash Point Method:CC
Flash Point:-14F,-26C
Lower Limits:1.0%
Extinguishing Media:FOAM, CO*2, DRY CHEMICAL
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED RESPIRATORY EQUIPMENT
TO AVOID INHALATION OF CONCENTRATED VAPORS. WATER SHOULD NOT BE
USED EXCEPT AS FOG TO KEEP NEARBY CNTNRS COOL.
Unusual Fire/Explosion Hazard:HANDLE AS FLAMM LIQ. VAPS FORM AN EXPLO
MIX IN AIR BETWEEN UPPER & LOWER EXPLO LIMITS, IGNITABLE BY PILOT
LIGHTS, OPEN FLAMES, ELECTRICAL MOTORS AND SWITCHES.

Spill Release Procedures:ELIMINATE IGNITION SOURCES, PROVIDE GOOD
VENTILATION, DIKE SPILL AREA AND USE ABSORBENT MATERIAL TO CLEANUP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:USE NON-SPARKING UTENSILS. AVOID HOT
METAL SURF. USE IN COOL, WELL VENTILATED AREAS.
Other Precautions:KEEP CNTNRS CLOSED WHEN NOT IN USE. KEEP AWAY FROM
EXCESSIVE HEAT & OPEN FLAMES. STRICTLY PROHIBIT SMOKING IN AREAS
WHERE THIS MATERIAL IS USED. USE TOOLS MADE OF ALUMINUM, BRASS OR
COPPER. PLASTIC UT ENSILS SHOULD NOT BE USED.

Respiratory Protection:WHEN SPRAYING THIS ADHESIVE USE A NIOSH/MSHA
APPRVD CARTRIDGE RESP/GAS MASK SUITABLE TO KEEP AIRBORNE MISTS &
CONCS BELOW TLVS. WHEN USING IN POORLY VENTED & CONFINED SPACES,
USE A NIOSH/MSHA APPRVD F RESH-AIR SUPPLYING RESP/SCBA.
Ventilation:GENERAL MECHANICAL VENT/LOCAL EXHAUST SHOULD BE SUITABLE TO
KEEP VAP CONC BELOW TLV. VENT EQUIP MUST BE EXPLOSION PROOF.
Protective Gloves:IMPERMEABLE GLOVES
Eye Protection:CHEM WORK GOG & FULL LGTH FCSHLD
Other Protective Equipment:IMPERMEABLE APRONS & PROTECTIVE CLOTHING
WHENEVER POSSIBLE. USE OF HEAD CAPS WHENEVER POSSIBLE IS STRONGLY
RECOMMENDED.
Work Hygienic Practices:EYE WASHES AND SAFETY SHOWERS IN THE WORKPLACE
ARE RECOMMENDED.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

Boiling Pt:B.P. Text:>132F,>56C
Vapor Pres:SEE INGRED
Vapor Density:> AIR
Spec Gravity:0.8
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NO
Appearance and Odor:BLUE, OFFENSIVE ODOR

Stability Indicator/Materials to Avoid:YES
ALKALINE MATERIALS, STRONG ACIDS AND OXIDIZING MATERIALS.
Stability Condition to Avoid:EXCESSIVE HEAT, POOR VENTILATION,
CORROSIVE ATMOSPHERES, EXCESSIVE AGING.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
OXIDES OF NITROGEN, AND POSSIBLE ACROLEIN.

Waste Disposal Methods:COLLECT ABSORBENT/SPILLED LIQUID MIXTURE & PLACE
INTO METAL CONTAINERS. CONSULT LOCAL, STATE & FEDERAL HAZARDOUS
WASTE REGULATIONS BEFORE DISPOSING INTO APPROVED HAZARDOUS WASTE
LANDFILLS. OBEY RELEVA NT LAWS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.